Product Description
Daniel Defense URG Complete Upper Receiver, M4A1 RIS II, 5.56 NATO, 14.5", Black/FDE
The Daniel Defense M4A1 Upper Receiver Group carries the RIS II picatinny quad rail, used by U.S. Special Operations Command in the SOPMOD Block II program since 2005. It is built around a 14.5 inch cold hammer forged M4 profile barrel with a permanently attached Daniel Defense extended flash suppressor, so on a stocked lower it builds a standard rifle, not an SBR.
This is part number 23-004-13150: a black upper receiver with a Flat Dark Earth RIS II rail. Like all Daniel Defense complete upper receiver groups, it includes an M16 profile bolt carrier group and the GRIP-N-RIP charging handle.
The SOPMOD Block II RIS II rail on a 14.5 inch pinned and welded M4 barrel.
M4A1 RIS II Rail
The M4A1 Rail Interface System II is CNC machined from 6061-T6 aluminum and Type III hard coat anodized in Flat Dark Earth. It free floats the barrel and gives you picatinny rail on four sides for a light, laser, grip or other accessories. Santoprene rail panels, heat resistant to 300 degrees F, protect your hand where you hold the rail. The RIS II is the rail many shooters picture when they think of a Block II carbine, and it is the heart of most clone builds.
14.5 Inch M4 Barrel, Pinned and Welded
Daniel Defense hammer forges its barrels in house from chrome moly vanadium steel. Cold hammer forging packs the steel tight around a mandrel, which gives long barrel life and consistent accuracy. Each barrel is chrome lined, Mil-Spec heavy phosphate coated and HP/MPI tested. The barrel is a 14.5 inch M4 profile with a 1:7 twist.
The extended Daniel Defense Flash Suppressor, 17-4 PH stainless steel with a salt bath nitride finish, is pinned and welded to the barrel, bringing the total length past 16 inches. A carbine-length gas system runs through a pinned low profile gas block machined from hardened 4140 steel.
Receiver, BCG and Charging Handle
The upper receiver is Mil-Spec with indexing marks and M4 feed ramps, CNC machined from 7075-T6 aluminum and Type III hard coat anodized. The bolt carrier group is M16 profile, Mil-Spec MP tested and chrome lined, with a properly staked gas key.
The GRIP-N-RIP charging handle has independent latches on both sides, so left- and right-handed shooters can run the rifle the same way. Sights are sold separately.
Installation and Compatibility
This upper receiver group fits any Mil-Spec AR-15 lower receiver. Install it with the two takedown pins, then function check before live fire. The pinned and welded flash suppressor brings the overall barrel length past 16 inches. Lower receiver, stock, magazine and optics are sold separately.
An upper receiver is not the regulated part of an AR-15, so it can ship directly to you where state and local law allow. Browse more Daniel Defense firearms or see AR-15 rifles if you would rather buy a complete gun.
Product Specifications
Manufacturer: Daniel Defense
Model: M4A1 Upper Receiver Group
Part Number: 23-004-13150
UPC: 815604016612
Caliber: 5.56mm NATO / .223 Remington
Barrel: 14.5 in., cold hammer forged CMV steel, chrome lined, M4 profile
Twist Rate: 1:7
Gas System: Carbine length, pinned low profile gas block
Muzzle Device: Daniel Defense Extended Flash Suppressor, pinned and welded
Handguard: Daniel Defense M4A1 RIS II, FDE
Sights: Sold separately
Finish: Black receiver, Flat Dark Earth rail
Weight: 4.56 lb
Included: Upper receiver, barrel, handguard, bolt carrier group, charging handle
Lower Receiver: Not included
Frequently Asked Questions
Is the muzzle device pinned and welded?
Yes. The extended flash suppressor is permanently attached, bringing the barrel past 16 inches.
What color is it?
The upper receiver is black and the RIS II rail is Flat Dark Earth.
Does it come with sights?
No. Sights are sold separately.
Does it include a bolt carrier group?
Yes. An M16 profile, MP tested, chrome lined BCG is included, along with the charging handle.
Is a lower receiver included?
No. This is an upper only; it fits any Mil-Spec AR-15 lower.
Do I need an FFL to buy it?
No. An upper receiver is not a firearm under federal law, but check your state and local laws.
Order the Daniel Defense M4A1 Upper Receiver Group from BattleHawk Armory and finish your Block II style build.
$1435.48
$1743.00
18% Discount
You save $307.52
In Stock
at BattleHawk Armory
Price checked 13 days ago
Key specs
Sold at BattleHawk Armory, $1,435.48 at the last check on Nov 8, 2026. One of 615 in-stock Daniel Defense Gun Parts from 30 stores on GearChase.
Store
BattleHawk Armory
Price checked
Nov 8, 2026
Daniel Defense Gun Parts
615 in stock, 30 stores
Brand
Daniel Defense
MPN
23-004-13150