Product Description
Noveske Irregular Defense Chainsaw Gen 4, 5.56 NATO, 11.5 in. Barrel, FDE Cerakote, Complete Upper
The Noveske Irregular Defense Chainsaw is a complete 11.5 in. 5.56 NATO upper built around Noveske's Chainsaw forged receiver and finished in FDE Cerakote. It arrives ready to pin onto a compatible lower with the barrel, handguard, bolt carrier group and charging handle already installed, and it is set up from the start to run well with a suppressor.
The barrel is 11.5 in. of 416R stainless steel with a 1:7 twist, a good match for the full range of common 5.56 and .223 bullet weights. It has a hand polished Noveske Match Chamber, is straight fluted between the chamber and gas block to save weight, and carries an individual serial number for quality control. A mid-length gas tube feeds a Noveske marked low profile gas block with a .750 in. journal that is pinned to the barrel so it cannot shift. The M4 barrel extension has extended, hand polished feed ramps, and the muzzle wears a CGS SCI-SIX flash hider that doubles as a suppressor mount.
The upper receiver is an IRGLR DFNSE marked Noveske Chainsaw forged from 7075-T6 aluminum with extended feed ramps. It is hardcoat Type III anodized, then coated in FDE Cerakote for a long lasting finish. A black nitride Noveske marked forward assist and an FDE Noveske Love Handle ambidextrous charging handle are installed, and the receiver has an anti-rotation interface with the handguard to keep the rail locked in line.
Inside is a phosphate coated, full auto compatible bolt carrier with a chrome lined carrier bore and key. The gas key is held by grade 8 American made bolts that are properly staked, and the phosphate bolt is made from heat treated Carpenter 158 steel and magnetic particle inspected.
Up front is a 4th Generation Noveske NSR 10.75 in. free float M-LOK handguard with M-LOK slots every 45 degrees and a 1913 Picatinny top rail. It mounts with a lightweight American made steel barrel nut. With the 11.5 in. barrel, the handguard ends .080 in. from the barrel thread shoulder, leaving clean spacing for a suppressor.
A note on barrel length: an upper with a barrel under 16 in. may only be installed on a lower that is configured and registered appropriately, such as an AR pistol lower or an approved short barreled rifle. Installing it on a standard rifle lower without approval creates an unregistered short barreled rifle, so check federal, state and local law before you build.
The Irregular Defense Chainsaw gives you a suppressor ready, Noveske built short upper in a finish that stands out on the rack.
Key Features
11.5 in. 416R stainless barrel, 1:7 twist, Noveske Match Chamber.
Mid-length gas with a pinned low profile gas block.
CGS SCI-SIX flash hider and suppressor mount.
Chainsaw forged upper, IRGLR DFNSE marked, FDE Cerakote.
Love Handle ambidextrous charging handle, FDE.
Full auto compatible BCG with staked grade 8 gas key bolts.
NSR 10.75 in. M-LOK free float handguard with Picatinny top rail.
Specifications
Manufacturer
Noveske
Model
Irregular Defense Chainsaw 11.5
Part Number
03002712
UPC
840906138564
Manufacturer
Noveske Rifleworks
Model
Irregular Defense Chainsaw 11.5 in.
MPN
03002712
UPC
840906138564
Caliber
5.56 NATO
Barrel length
11.5 in.
Barrel material
416R stainless steel
Twist
1:7
Chamber
Noveske Match Chamber, hand polished
Barrel profile
Straight fluted between chamber and gas block
Gas system
Mid-length
Gas block
Low profile, .750 in. journal, pinned
Barrel extension
M4, extended hand polished feed ramps
Muzzle device
CGS SCI-SIX flash hider and suppressor mount
Upper receiver
Noveske Chainsaw, forged 7075-T6 aluminum, IRGLR DFNSE marked
Finish
Hardcoat Type III anodized, FDE Cerakote
Forward assist
Black nitride, Noveske marked
Charging handle
Noveske Love Handle, ambidextrous, FDE
Bolt carrier
Phosphate, full auto compatible, chrome lined bore and key
Bolt
Phosphate, Carpenter 158 steel, MPI tested
Handguard
4th Gen Noveske NSR 10.75 in. M-LOK, free float, Picatinny top rail
Barrel nut
Steel, American made
FAQs
What caliber is it?
5.56 NATO, with a 1:7 twist 416R stainless barrel.
What gas system does it use?
Mid-length.
Is it suppressor ready?
Yes. It has a CGS SCI-SIX flash hider and suppressor mount, and the handguard leaves .080 in. of clearance to the thread shoulder.
Does it come with a bolt carrier group and charging handle?
Yes. A full auto compatible BCG and an FDE Love Handle ambidextrous charging handle are installed.
Can I put it on any AR-15 lower?
It fits standard AR-15 lowers, but with an 11.5 in. barrel it must go on a pistol lower or a registered short barreled rifle.
Compare more complete uppers, complete uppers at BattleHawk Armory.
$1600.00
In Stock
at BattleHawk Armory
Price checked 6 days ago
Product Details
Brand
Noveske Rifleworks
MPN
03002712