Interlux Nautical Super ProGuard Antifouling PaintSold in GallonsProGuard is performance, value and reliability all in one. ProGuard is a hard modified epoxy, low V.O.C., high copper antifouling paint formulated to effectively provided year round protection in warm waters or where fouling is at its worst. ProGuard can be applied directly over most properly prepared antifouling paints. Recommended for use on the underwater areas of fiberglass, wood, and properly primed metal (except aluminum) boat hulls and can be used in fresh, salt and brackish waters. Hard modified epoxy; Long lasting year round performance; High copper, for excellent performance in high fouling waters; Compatible over most antifouling paints; Low V.O.C.; Specifications: Finish: Matte; Number of Coats: 2 coats, 3 on bare wood; Coverage: 470 sq. ft/gal; Application Methods: Brush, roller, airless and conventional spray; Colors Available:Do not use on aluminum.***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***How to ApplyAPPLICATION DATA METHOD: Airless Spray, Brush, Conventional Spray, Roller NUMBER OF COATS: 2, 3 on bare wood DRY FILM THICKNESS PER COAT: 2 mils (3.5 mils wet)COVERAGE: 470 sq. ft/gal. APPLICATION TEMP: 50F Min. / 95F Max.THINNER: Special Thinner 216DRY TIMES:TempTo TouchTo RecoatTo Launch95F30 MIN1 HR6 HR73F1 HR2 HR8 HR50F2 HR6 HR12 HRPREVIOUSLY PAINTED SURFACES - GOOD CONDITION: Remove all traces of loose paint by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with XyleneA using the two-rag method before and after sanding. Apply two coats of Super ProGuard allowing for appropriate dry times.PREVIOUSLY PAINTED SURFACE - POOR CONDITION: Completely remove old antifoulingpaint, after all old antifouling paint has been completely removed, sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with XyleneA using the two-rag method before and after sanding. Apply two coats of Super Proguard allowing for appropriate dry times. BARE FIBERGLASS: Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove mold release wax and surface contamination by wiping down the surface with XyleneA using the two-rag method. Fill any surface imperfections with approved filler for underwater use. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with XyleneA using the two-rag method. Apply two coats of Super ProGuard allowing for appropriate dry times. BARE WOOD: Sand the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with XyleneA using the two-rag method before and after sanding. Apply the first coat of Super Proguard thinned 10% with XyleneA^2. Apply two finish coats of Super Proguard allowing for appropriate dry times.UNDERWATER METALS: Apply an approved underwater metal primer as per manufacturer's instructions. Apply two coats of Super Proguard allowing for appropriate dry times. Do not use on aluminum.APPLICATION METHODS: Mixing: Stir well before use.Cleaner: Acetone or XyleneA Thinning: Thin 10% with XyleneA^2. Do not exceed 10% by volume.Ventilation and Humidity Control: Apply in dry, well ventilated conditions.Roller: Use a 3/8" nap solvent resistant roller.Airless Spray: Tip Size: 0.53-0.66 mm/21-26 thou. Pressure: 170-204 bar/2500-3000 psi.Conventional Spray: Pressure Pot: Tip Size: 1.8-2.2 mm/70-85 thou. Pressure: 4.08-4.76bar/60-70psi (gun pressure); 10-15 psi (pot pressure).