Interlux Pre-Kote Brightside Boat Primer - WhiteAs one of the largest manufacturers of marine paints and primers, Interlux is a name you can trust for high-quality products that provide long-lasting protection for your boat finishes. The innovative technology has been leading the way for over a century in boat primers and paints, including the Interlux Pre-Kote boat primer. Interlux's commitment to research and development has helped to create a high-performance boat primer that has stood the test of time.Pre-Kote is an Interlux primer used to help protect boat surfaces above the waterline. Before applying Interlux Pre-Kote Brightside you should prepare your surfaces. Interlux primer is safe to use on fiberglass, wood, and previously painted surfaces.The application should be done with a brush, airless sprayer, or roller. Interlux primer is a high solid and heavy application that can cause solvent entrapment. It is recommended to apply 1-2 coats, depending on desired thickness. Make sure to correct surface imperfections before application. Sanding between each application is recommended for optimal application. Interlux Pre-Kote Brightside is available in quarts and gallons. Each gallon covers 450 sq/ft. Specifications: Finish: Matte; Application Method: Brush, roller or spray; Number of Coats: 1-2; Coverage: 400 sq. ft/gal per coat brush applied; Associated Products:Interlux Brush Thinner: Thinning for brush application and clean-upInterlux Special Thinner: Thinning for spray application and clean-upDo not use this product on aluminum hulls or outdrivesHow To Apply Pre-Kote PrimerInterlux Pre-Kote is compatible with the following Interlux paints: Brightside, Premium Yacht Enamel, Interdeck, Bilgekote, and any single part finish. Do not use Perfection or any two-part catalyzed product over Pre-Kote. Application Method: Airless Spray, Brush, Conventional Spray, Roller- Pressure Pot or Siphon Cup; Number of Coats: 1-2 As Needed; Dry Film Thickness per Coat: 2 mils (3.5 wet mils); Coverage: 450 sq. ft/gal.; Application Temp: 50F Min. / 95F Max.; Thinner: Brushing Liquid 333; DRY TIMES: Temp To Recoat To Touch 95F 6 HR 1 HR 73F 8 HR 2 HR 50F 12 HR 3 HRNote: Pre-Kote must be sanded between coats.Surface Preparation & Application Previously Painted Surfaces; Sand old surfaces with 120 grit paper and remove sanding residue.; Wipe with Brushing Liquid 333.; Repair surface defects with Surfacing Putty.; Sand surface, then wipe clean.; Bare Wood; Sand with 80 grit paper then wipe with Brushing Liquid 333.; Repair surface defects with Surfacing Putty.; For Plywood, follow the above instructions, then apply Inter-Prime Wood Sealer Clear 1026.; For Mahogany, follow the above instructions, then apply Pre-Kote directly to the wood.; Bare Fiberglass; Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202.; While surface is still wet, wipe with a clean, dry rag.; Continue this process until the entire surface has been cleaned.; Sand with 80 grit paper, then wipe with Fiberglass Solvent Wash 202.; Repair surface defects with Watertite Filler.; Sand surface, then wipe clean.; Application InformationApply 1-2 coats depending on surface condition. Allow the necessary overcoating time between applications. Sand between primer coats with 120 grit paper until translucent. Remove sanding residue with a rag dampened with Brushing Liquid 333. Apply finish coats. Large surface imperfections should be filled prior to application.; It is good practice to apply the finish enamel soon after sanding to avoid surface contamination.; Refer to the application instructions PDF below for pressure and tip sizes for airless and conventional spray applications.; Pre-Kote is a high solid primer. Avoid a heavy application as this may lead to solvent entrapment.; Apply to clean, dry, properly prepared surfaces only.; Click to Download Interlux Pre-Kote Primer Application Instructions