Pettit Black Widow Hard Racing Bottom Paint
Pettit Black Widow Hard Racing Bottom Paint, Pettit Black Widow Hard Racing Bottom PaintPettit's Black Widow Bottom Paint is the slickest, fastest, ultra-smooth, burnishable racing finish available. Its powerful dual biocides provide high-performance, multi-season protection in all waters. Black Widow also contains four strong slickening agents including Molybdenum Disulfide, PTFE, Graphite, and Silicon, making it the fastest racing paint available. Black Widow is easily applied by roller, brush, or spray and is easily burnishable to a metallic "gun-metal" shine. Black Widow makes an excellent paint for the bottom of any boat where speed is the number one priority including racing sailboats and high performance offshore powerboats.Features: Slickest, fastest, and easiest to clean racing paint; Contains four slickening agents; Provides high performance, multi-season, dual-biocide antifouling protection; Can be polished to mirror-like finish; Specifications: Colors Available: 1869 Black, 1269 Dark Blue; Sizes Available: 1 US Quart, 1 US Gallon; Finish: Flat; Coverage: 440 ft2/gal.; VOC: 330 grams/liter (max); Biocide: Cuprous Thiocyanate - 25.0% | Zinc Pyrithione - 2.50%; Associated Products:Pettit 120 Brushing Thinner - For thinning and surface preparationPettit 121 Spray Thinner - For thinningPettit Protect Epoxy Primer - For bare fiberglass applicationHow Much Pettit Black Widow Do I Need for My Boat?Refer to the chart below to calculate how much Black Widow paint you will need for your boat. Calculate the square footage of the hull to be painted - multiply the length of the hull by the beam then multiply that total by .85; Divide that number (your square foot total) by the amount of coverage Black Widow provides. (440 square foot per gallon). This will give you a one-coat total.; Example: If your boat has a length of 28', and a beam of 8.5', you will multiply 28 x 8.5 x .85 to get your total square footage. The total square footage for this boat is 202.3 square feet. A gallon of Black Widow has a coverage of 440 square feet per gallon for one coat, so one gallon will be enough for two coats.How to Apply Pettit Black Widow Hard Racing Bottom PaintPettit Black Widow Bottom Paint is easily applied by brush, roller, or spray. When rolling, only use a high-quality short nap (3/16" maximum) roller cover. Mix paint thoroughly prior to application to ensure ingredients are evenly dispersed throughout the can. All surfaces must be clean, dry, and properly prepared prior to painting. Do not apply Black Widow directly on aluminum hulls or outdrives without properly priming first. When spraying, do not thin Black Widow more that 5% or inadequate film thickness will occur.Burnishing of Black Widow to create a slicker finish can be done with 400 - 1200 grit wet or dry sandpaper after the coating has dried for at least 48 hours to achieve a smooth but matte finish. For a glossy finish, sand with 3000-5000 grit sandpaper. If burnishing, a third or fourth coat of Black Widow is recommended depending on application method. Application Method: Brush, roller, airless or conventional spray.; Number of Coats: 1 minimum per season with additional coats for extended service; Dry Film Thickness: 2 mils (3.6 wet mils); Coverage: 440 sq. ft/gal.; Application Temp: 50F Min. / 90F Max.; Thinner: 120 Brushing Thinner. 121 Spraying Thinner, or 120VOC Thinner; DRY TIMES:TempTo RecoatTo Launch90F1 HR4 HR70F2 HR8 HR50F6 HR24 HRSurface Preparation and Application SystemsPreviously Painted Surfaces Black Widow can be applied over most aged hard antifouling coatings.; Old tin copolymers must be removed completely or sealed with Tie-Coat Primer before applying Black Widow.; If previous coating is in good condition:; Thoroughly sand with 80 grit sandpaper then solvent clean with 120 Brushing Thinner.; Apply two thin coats of Black Widow.; If previous coating is in poor condition:; Remove to the bare surface by sanding or using paint remover.; Proceed with one of the bare systems below.; Bare Fiberglass All bare fiberglass should be thoroughly cleaned with Pettit 92 Bio-Blue Hull Surface Prep or dewaxed several times with D95 Dewaxer.; Proceed with either Sanding Method or the Non-Sanding Methods below.; Sanding Method:; Sand thoroughly with 80 grit production paper to a dull, frosty finish.; Rewash surface with Pettit 120 or 120VOC Brushing Thinner to remove residue.; Apply two finish coats of Black Widow.; Non-Sanding Method:; Thoroughly clean, de-wax, and etch the surface with 92 Bio-Blue Hull Surface Prep using a medium Scotch-Brite pad.; Thoroughly rinse all residue and let dry.; Apply one coat of Pettit Protect Epoxy Primer.; Apply two thin finish coats of Black Widow.; Bare Wood Sand thoroughly with 80 grit sandpaper and wipe clean using Pettit 120 or 120VOC Brushing Thinner.; Apply a coat of Black Widow thinned 25% with Pettit 120 or 120VOC Brushing Thinner.; Allow an overnight dry, lightly sand, and wipe clean.; Apply two thin finish coats of Black Widow.; Bare Steel and Cast Iron Remove loose rust and scale from the metal surface by sandblasting or wire brushing.; Immediately clean surface with vacuum or fresh air blast.; Apply two coats of Pettit Rustlok Steel Primer, allowing each to dry only 1-2 hours before over coating.; Follow by two coats of Pettit Protect Epoxy Primer.; If fairing is required, apply Pettit EZ-Fair between the two coats of Pettit Protect.; Apply two thin finish coats of Black Widow.; Click to Download Pettit Black Widow Bottom Paint Application Instructions